TABLE 1-9. EQUIPMENT SUPPLIED   Click here to make tpub.com your Home Page Page Title: TABLE 1-9

Table 1-1. Accesories Supplied Order this information in Print Order this information on CD-ROM Download in

the modulated signal with the rf carrier removed, The rf signal is supplied to the

a summary of the functions of the a. Equipment Supplied. BTS equipment units. b

by the keyboard entries. The rf output from synthesizer assembly A4 is supplied to rf

the generator. When an rf carrier frequency is selected, data from the CPU is supplied over the control

g. RADSCOM diskette (PIN 29725200) (supplied with the AVA) h. INITCAL diskette (PIN 29304200) (supplied with the Electronic

slope mode, TDM board A2A3 generates 90- and 150-Hz signals. These signals are supplied to analog

generated, data on the Input of the I/O port Is supplied to the

applied to assembly A3. Rf modulator assembly A3 sends frequency and status information supplied by synthesizer assembly A4

11 and the analog test adapter in p1-12. Program cards are supplied with the 1

and -65V.   The voltages +5 V, +15 V, and -15 V are supplied to the

10. TABLE 1-2. LEADING PARTICULARS SPECIFICATION CHARACTERISTIC +28 V (+24 to +29 V) supplied Power Requirements* through LRU

from the P Repair parts which are stocked in or supply system. supplied from the GSA

A201 and locked autosyn i. Nine cables and one test adapter are supplied for B

7. Purpose and Use i n a case and is supplied with nine electrical cable

pulse is available at Blanking Jack J6 to simulate the blanking pulse supplied to LRU

13 a.   Control-Interface Unit (fig. 1-2). The Three extender cards are supplied with the data

of the DAU is achieved by programming the CADU with the supplied software via a

7(+) and AIPS2- a. General.   Only the standard hand tools 6. supplied with Tool Kit, Electronic

claim. The form required to file such a claim will be supplied by the carrier

Video Assembly 1A2.  In normal operation, the modulated RF signal is then supplied through RF Switch (A3

from equipment and save it for repacking. Check that power cable is supplied with test set. Inspect

the FLTS and its operational requirements: +28 V (+24 to +29 V) supplied through Power Requirements LRU

FUSE F1. Fuse F1 provides test set circuit protection. POWER CABLE. An ac power cable is supplied with the test

be allowed to come up around the cup . Thermometers: Thermometers are not supplied with the Flash

Generation.   The conical scan frequency generator (1) produces a triangle wave, which is supplied to the

occur, address, data, and 1/0 write pulses from the cpu are supplied over the control

a self test signal from Video Assembly 1A2 operates RF Switch (A3).  RF signals are then supplied from Transmitter Assembly 1A1

of the functions of the FLTS equipment units. TABLE 1-3. EQUIPMENT SUPPLIED FUNCTION QTY NOMENCLATURE Tests

O N Figure 1-1. Pilot And Static Systems Tester Table 1-1. Accesories Supplied Chapter 2 Operating Instruction

and  ports  on  the  tester  along  with  external  hoses  and  adapters supplied with the tester

115 volts ac + 1 percent, 50 to 500 cycles, three- phase. 1-6. Accessories Supplied. Accessories   sup- plied with

of AR 380-41, and depot level. which are stocked and supplied by the e

tested are The digital tester sups the test number being run, test supplied to the

the power supply  receptacle  is  properly  polarized and  grounded. As  delivered, it is supplied with a standard

to functionally test the Universal Tracking Device (UTD). b. Electrical System.  Primary power is supplied from the DAU

LRU-1. 6 PWR Indicator Lamp Lights green to indicate that +28 Vdc is supplied to the

accessible  when  the  cover  is  open  or removed from the Tester.  Accessories supplied with the Tester

FLTS transmitter assembly 1A1 via cable W2. PWR indicator - when lit (green), indicates that +28V is supplied to video

Also, a power connector is provided through which AC and DC power is supplied to the

CABLE INFORMATION FIGURE TABLE 1-8. BTS CABLE INFORMATION (Continued) EQUIPMENT CONFIGURATION TABLE 1-9. EQUIPMENT SUPPLIED SAFETY, CARE AND

O N Figure 1-1. Pilot And Static Systems Tester Table 1-1. Accesories Supplied Chapter 2 Operating Instruction

CABLE INFORMATION FIGURE TABLE 1-8. BTS CABLE INFORMATION (Continued) EQUIPMENT CONFIGURATION TABLE 1-9. EQUIPMENT SUPPLIED SAFETY, CARE AND